1．Download：

 【Software】 【64Driver】 【Manual】 【Firmware】 【SDK】

 2．Accessories： 

3.Other Pictures

Connected to the computer can be used as a virtual oscilloscope

4. Characteristic（Handheld Oscilloscope/Multimeter）

全隔離手持示波表，示波器通道間完全隔離，示波器和萬用表通道隔離，示波器、萬用表與USB等通訊接口之間完全隔離，隔離等級:1000V CATII,600V CATIII.

High Bandwidth 60MHz-200MHz Oscilloscope,1GS/s sample rate, and 6000 Counts DMM with analog bargraph , and data recorder.

2M Memory Depth.

High Refresh Rate （2500 frames）

Large 5.6 inch TFT Color LCD Display，High Resolution（640*480）, Dual-Window Design --More clear, More Detailed

One-touch automatic setup optimizes the position, range, timebase, and triggering to assure a stable display of virtually any waveform

Easy-to-use pop-up menu with built-in multi-language help system

23 Automatic Measurements

Waveform Math: Add, Subtract, Multiply, and Divide

Store and recall over

Automatic cursor tracking measurements

XY Mode

Built-in FFT function converts a time-domain signal into its frequency components to measure harmonic content and distortion in systems

Waveform Recorder to capture/replay input waveforms from CH1 and CH2 with a maximum record length of 1000 frames

Pass-Fail function compares a stored waveform to an unknown input

Average Mode for smoothing waveforms

Square Wave Output （2V, 1kHz） for probe adjustment

USB Host/Device 2.0 full-speed interface ,support removeable disk, LAN Optional ,Easy to control by PC or long-distance.

Dimensions （mm）:240（L）x165（W）x50（H）, be carried easily.

LabviewVBVC Second Design instance.

5. Hardware Specification

Model

DSO1202S

DSO1122S

DSO1062S

Oscilloscope mode

Bandwidth

200MHz

120MHz

60MHz

Real-time Sample Rate

1GSa/s

Equivalent Sample Rate

25GSa/s

SEC/DIV Range

2nS/div-2000S/div （in a 2, 4, 8 sequence）

Delay Time Accuracy

500ps

Vertical

A/D Converter

8-bit resolution

VOLTS/DIV Range

2mV/div～5V/div at input BNC

Position Range

50V（5V/div）, 40V（2V/div～500mV/div）, 2V（200mV/div～50mV/div） 400mV（20mV/div～2mV/div）

Record Length

Single-channel: Maximum 2M; Dual-channel:Maximum 1M

Trigger

Trigger Sensitivity
（Edge Trigger Type）

DC: CH1/CH2（Typical） 1div from DC to 10MHz;1.5div from 10MHz to Full

AC: Attenuates signals below 10Hz

HF Reject: Attenuates signals above 80kHz

LF Reject: Attenuates signals below 150kHz

Noise Reject: Reduces trigger sensitivity

Trigger Level Range

CH1,CH2: 8 divisions from center of screen

Trigger Level Accuracy,
typical （Accuracy is for signals having rise and fall times 20ns）

CH1,CH2: （0.3div V/div） （within 4 divisions from center of screen）

Holdoff Range

100ns-10s

Trigger Type

Edge

Trigger on the rising or falling edge

Pulse Width

Trigger （when , ,=, ） on positive or negative pulses
Pulse Width Range: 20ns-10s

Video

Trigger on an NTSC, PAL, or SECAM standard video signal
Line Range: 1-525 （NTSC）, 1-625 （PAL/SECAM）

Slope

Trigger （when , ,=, ） on a positive or negative slope
Set Time: 20ns 10s

Overtime

from the rising or falling edge
Set Time: 20ns-10s

Alternate

Internal trigger on edge, pulse width, video or slope

Measurement

Cursors

Manual: The difference between voltage cursors △V; the difference between time cursors △T; 1/△T calculated by Hz.
Tracing: The voltage and time at a waveform point

Automatic

Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width

Meter Mode

Max.Resolution

6,000 Counts

DMM Testing Modes

Voltage, Current, Resistance, Capacitance,Diode Continuity

Max. Input Voltage

AC: 600V, DC: 800V

Max. Input  Current

AC: 10A, DC: 10A

Input Impedance

10 M

Isolation

The float voltage between BNC and Ground

600V CATIII, 1000V CAT II

The float voltage between each Channel

600V CATIII, 1000V CAT II

The float voltage between Multimeter and Ground

1000V

between input Ports directly

400V CAT II

Input by 10:1 probe

600V CATIII, 1000V CAT II

The Max input voltage of Multimeter

DC 800V,AC 600V

Display

Type

Right angle 5.6 16-digit color LCD

Resolution

640*480 dots

Contrast

16 gears, with the progress bar to show adjustment

Interface

USB host and USB slave, Lan Optional

Power Supply

Voltage

 DC Input:12--17VDC, 2000mA

Mechanical

Size

245 x 163 x 52 （mm）

Weight

1.3KG （exclusive of packing and accessories）

6．Software：

Operating system: Windows NT, Windows 2000, Windows XP ,VISTA

7．SecondDesign：

   Supply DEMO code （VC、VB、LABVIEW）

以上信息由企業(yè)自行提供，信息內容的真實性、準確性和合法性由相關企業(yè)負責，91化工儀器網(wǎng)對此不承擔任何保證責任。

溫馨提示：為規(guī)避購買風險，建議您在購買產品前務必確認供應商資質及產品質量。